Rubber sheet
The rubber membrane is adhered or fastened in black or white.
Flat Roofing
Rubber Roof Installation Oradell, NJ
Installing a rubber roof in Oradell means choosing the EPDM thickness and attachment method, then flashing walls, curbs and edges so the membrane can move without tearing, and explain each choice before the sheet is rolled out. One call to (551) 383-2310 reaches a nearby rubber roof installer.
A true rubber roof is EPDM, a synthetic rubber membrane used on flat and low slope roofs for decades. It comes in large, flexible sheets, most often black, in 45 or 60 mil thickness, and its biggest strength is that it stays flexible in heat and cold without cracking. That flexibility is why it suits so many homes.
EPDM can be attached in three main ways. The sheet can be glued to the substrate, fastened with plates at the seams or laid loose under a layer of stone. Residential roofs are most often fully adhered.
Two more decisions round out the plan. Sixty mil EPDM costs a little more than 45 mil but resists punctures better and lasts longer. Black EPDM absorbs heat, which helps in cold climates, while white EPDM reflects sun and keeps rooms below cooler. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
Rubber Roof Installation is often paired with rubber roof repair and flat roof installation, depending on the cause.
Need rubber roof installation in Oradell? Call (551) 383-2310 to reach a nearby roofing contractor.
Call nowThe process
What happens during a rubber roof installation
Here is how a roofer typically installs an EPDM roof.
Deck prep
The deck is repaired and checked for slope, ideally a quarter inch per foot toward drains or gutters. Old roofing is removed if the roof is being replaced.
Install insulation
Insulation boards go down for energy savings and slope, topped by a smooth cover board. Low spots can be corrected with tapered insulation.
Sheet layout
The EPDM is unrolled, positioned and left to relax so wrinkles flatten before any adhesive goes on. Laps are arranged so water flows over them.
Bond the membrane
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Each half gets the same treatment in turn. Brooming from the middle outward pushes trapped air to the edges.
Seal the seams
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Tape edges are finished with lap sealant.
Flash the details
Flashing goes up walls and around curbs, with boots at pipes and new edge metal at the perimeter. Counter flashing covers the top of wall flashing. A final walk checks every seam with a probe before the job is closed out.
What is included
What goes into a rubber roof
Seams
Every seam gets primer and tape with lap sealant at the edges.
Cover board
Insulation adds energy savings and slope and gives the adhesive a firm grip.
Edge metal
Termination bar, pipe boots and edge metal are installed to keep water out.
Tear-off
The base is cleared and checked for a sound start.
Related service
EPDM Roof Installation Oradell, NJ
EPDM roof installation is straightforward in concept and demanding in the details. The membrane has to lie flat on a clean, dry cover board, the adhesive has to reach the right tack before the sheet is laid and every seam has to be primed and rolled with care. Dry, mild days give the best bond. Some installers use water-based adhesive for the field of the roof and solvent-based adhesive at walls and curbs, where the grip has to be strongest.
A good Oradell installer also plans for movement. Perimeter securement and proper flashing help prevent the shrinkage problems older rubber roofs show. Ask how the roofer secures the perimeter.
Local help
Rubber Roof Installation Near Me
Around Oradell, homeowners often choose EPDM for flat roof sections because it is durable and easy to repair. Across Oradell and nearby towns like Emerson, New Milford, Haworth and Paramus, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, which is why the seams and flashing deserve careful attention.
Searching for rubber roof installation near me from Oradell or Emerson, New Milford, Haworth and Paramus? Call (551) 383-2310 to talk to a roofer who works in your part of town.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Oradell is busiest after a hard winter and before the next one.
Why call
Why act early
Smaller repairs
Small roof problems caught early usually stay small repairs.
Roofers who know Oradell
Roofers in Oradell know the roof types and weather wear common in local homes.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Rubber Roof Installation questions
What is the lifespan of a new EPDM roof?
Rubber roofs often last decades. Good seams, drainage and occasional checks make the difference. Repairs are simple when needed.
Can a rubber roof go over an existing roof?
Recovering depends on the condition of the old roof. The old roof must be a single dry layer, with a recover board over it. If the old roof is wet, it must come off. Core samples or a moisture scan show whether the old roof is dry enough.
What is the difference between EPDM and TPO?
EPDM is synthetic rubber, while TPO is a thermoplastic membrane. EPDM is usually black, very flexible and seamed with tape, while TPO is usually white, more reflective and heat welded at the seams. A roofer can help you choose.
What color EPDM is best?
The choice depends on the climate and the space below. White helps in sunny climates, and black is common where winters are long. Talk through the choice with a roofer.
How thick should a rubber roof be?
The common choices are 45 mil and 60 mil. Thicker 60 mil is tougher and longer lasting. Heavy duty options exist too.
More questions? Call (551) 383-2310
Related services
Rubber Roof Repair
Fixing open seams, punctures, shrinkage and split flashing on EPDM rubber roofs, after the real leak point is found.
Learn moreFlat Roof Installation
Installing TPO, PVC, EPDM or modified bitumen roofs on additions, garages, porches and flat-roof homes, so water drains instead of ponding.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, sized to the deck, the drains and the way the roof is used.
Learn moreFlat Roof Replacement
Full replacement of failing flat roofs, with a moisture survey deciding tear-off or recover, so ponding and repeat leaks end for good.
Learn more
Looking for something else?
See all roofing servicesGet rubber roof installation help in Oradell
Call (551) 383-2310 for a local roofer in Oradell and nearby towns.